Refine
Document Type
- Article (29)
- Part of a Book (14)
- Conference Proceeding (1)
- Master's Thesis (1)
Has Fulltext
- yes (45)
Keywords
- Biogas (4)
- Digitaler Zwilling (3)
- HIV (3)
- Heterogeneous Catalysis (3)
- Lipase (3)
- Process Analytical Technology (PAT) (3)
- Virus-like Particles (VLPs) (3)
- Advanced Process Control (APC) (2)
- CALB (2)
- Cumene Hydroperoxide (2)
Faculty
- Angewandte Naturwissenschaften (F11) (45) (remove)
Electroplating generates high volumes of rinse water that is contaminated with heavy metals. This study presents an approach for direct metal recovery and recycling from simulated rinse water, made up of an electroplating electrolyte used in industry, using reverse osmosis (RO). To simulate the real industrial application, the process was examined at various permeate fluxes, ranging from 3.75 to 30 L·m−2·h−1 and hydraulic pressures up to 80 bar. Although permeance decreased significantly with increasing water recovery, rejections of up to 93.8% for boric acid, >99.9% for chromium and 99.6% for sulfate were observed. The final RO retentate contained 8.40 g/L chromium and was directly used in Hull cell electroplating tests. It was possible to deposit cold-hued chromium layers under a wide range of relevant current densities, demonstrating the reusability of the concentrate of the rinsing water obtained by RO.
Polyimides rank among the most heat-resistant polymers and find application in a variety of fields, including transportation, electronics, and membrane technology. The aim of this work is to study the structural, thermal, mechanical, and gas permeation properties of polyimide based nanocomposite membranes in flat sheet configuration. For this purpose, numerous advanced techniques such as atomic force microscopy (AFM), SEM, TEM, TGA, FT-IR, tensile strength, elongation test, and gas permeability measurements were carried out. In particular, BTDA–TDI/MDI (P84) co-polyimide was used as the matrix of the studied membranes, whereas multi-wall carbon nanotubes were employed as filler material at concentrations of up to 5 wt.% All studied films were prepared by the dry-cast process resulting in non-porous films of about 30–50 μm of thickness. An optimum filler concentration of 2 wt.% was estimated. At this concentration, both thermal and mechanical properties of the prepared membranes were improved, and the highest gas permeability values were also obtained. Finally, gas permeability experiments were carried out at 25, 50, and 100 ◦C with seven different pure gases. The results revealed that the uniform carbon nanotubes dispersion lead to enhanced gas permeation properties.
Biogas, mit geringen Konzentrationen an Methan, entsteht unter anderem bei verschiedenen industriellen Prozessen. Wegen der Umweltschädlichkeit des Methans gilt es dessen Eintrag in die Umwelt zu vermeiden.
Das Ziel des vorgestellten Projektes war die Überprüfung eines umweltfreundlichen Verfahrens zur Reduzierung des Methans durch methanotrophe Bakterien. Die einzelnen Batchversuche liefen über 15 Stunden und zeigten eine starke Reduzierung des Methans von 18 auf 1 Vol.-%.
STEPsCON 2018 was jointly organized by the Faculty of Applied Natural Sciences of TH Köln (Germany) and the University of Oulu (Finland) on the occasion of the 50th anniversary of the Leverkusen – Oulu town twinning. The conference focused on sustainability issues and covered the current state of research in four key topics:
1. Sustainable Medicine and Pharmaceuticals
2. Resources and Bioremediation
3. Sustainable Chemistry & Industrial Biotechnology
4. Innovative Materials & Formulations
Agents with antifungal activity play a vital role as therapeutics in health care, as do fungicides in agriculture. Effectiveness, toxicological profile, and eco-friendliness are among the properties used to select suitable substances. Furthermore, a steady supply of new agents with different modes of action is required to counter the well-known potential of human and phyto-pathogenic fungi to develop resistance against established antifungals. Here, we use an in vitro growth assay to investigate the activity of the calcineurin inhibitor tacrolimus in combination with the commercial fungicides cyproconazole and hymexazol, as well as with two earlier reported novel {2-(3-R-1H-1,2,4-triazol-5-yl)phenyl}amines, against the fungi Aspergillus niger, Colletotrichum higginsianum, Fusarium oxysporum and the oomycete Phytophthora infestans, which are notoriously harmful in agriculture. When tacrolimus was added in a concentration range from 0.25 to 25 mg/L to the tested antifungals (at a fixed concentration of 25 or 50 mg/L), the inhibitory activities were distinctly enhanced. Molecular docking calculations revealed triazole derivative 5, (2-(3-adamantan-1-yl)-1H-1,2,4-triazol-5-yl)-4-chloroaniline), as a potent inhibitor of chitin deacetylases (CDA) of Aspergillus nidulans and A. niger (AnCDA and AngCDA, respectively), which was stronger than the previously reported polyoxorin D, J075-4187, and chitotriose. The results are discussed in the context of potential synergism and molecular mode of action.
Current changes in environmental legislation and customer demands set an urge for the development of more sustainable surfactants. Thus, the objective of this work was the development of novel environmentally friendly amino acid surfactants. Combining Diels–Alder cyclization of myrcene with maleic or citraconic anhydride followed by ring opening with amino acids enabled a synthesis route with a principal 100% atom economy. Variation of amino acids resulted in a large structural variety of anionic and amphoteric surfactants. Lysine gave access to either a mono-acylated product bearing a cationic side chain or a bi-acylated gemini surfactant. First, anhydride precursors were synthesized in yields of >90% in a Diels–Alder reaction under microwave radiation and subsequent amino acid coupling in aqueous environment gave fully bio-based surfactants in good yields and purity. Physicochemical characterization showed an enhanced decrease in surface tension upon addition of amino acids to the myrcene–anhydride backbone, resulting in a minimal value of 31 mN·m−1 for gemini–lysine. Foamabilitiy and foam stability were significantly increased at skin-friendly pH 5.5 by incorporation of amino acids. The carboxylic groups of surfactants with arginine were esterified with ethanol to access cationic compounds. Comparative analysis revealed moderate antimicrobial effects against yeast, Gram-positive bacteria, and Gram-negative bacteria.
Comparative analysis of non-natural acceptor glucosylation with sucrase enzymes of family GH 70
(2019)
Mutan- and alternansucrase were analyzed for their non-natural glucosylation potential with catecholic compounds caffeic acid and nordihydroguaiaretic acid (NDGA) as well as with non-catecolic p-coumaric acid and umbellic acid. Mutansucrase accepted both catecholic substrates and high glucosylation yields of 92 % with caffeic acid and 81 % with NDGA were obtained. The enzyme showed a clear regio-preference for the catechol 4-OH, which corresponds to findings from our previous work with Leuconostoc and Weissella derived glucansucrases. The substrate spectrum of the alternansucrase was broader and all substrates were successfully glucosylated with a preference for the catechols. Interestingly alternansucrase possessed a different regio-specificity. With caffeic acid the 3-O-α-D-glucoside was the major product. A similar substrate spectrum and regioselectivity pattern was observed in previous glucansucrase screenings only with glucansucrase from strain Weissella beninensis DSM 22752. Therefore it may be concluded that the W. beninensis enzyme is an alternansucrase type enzyme as well.
The development and adoption of digital twins (DT) for Quality-by-Design (QbD)-based processes with flexible operating points within a proven acceptable range (PAR) and automation through Advanced Process Control (APC) with Process Analytical Technology (PAT) instead of conventional process execution based on offline analytics and inflexible process set points is one of the great challenges in modern biotechnology. Virus-like particles (VLPs) are part of a line of innovative drug substances (DS). VLPs, especially those based on human immunodeficiency virus (HIV), HIV-1 Gag VLPs, have very high potential as a versatile vaccination platform, allowing for pseudotyping with heterologous envelope proteins, e.g., the S protein of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). As enveloped VLPs, optimal process control with minimal hold times is essential. This study demonstrates, for the first time, the use of a digital twin for the overall production process of HIV-1 Gag VLPs from cultivation, clarification, and purification to lyophilization. The accuracy of the digital twins is in the range of 0.8 to 1.4% in depth filtration (DF) and 4.6 to 5.2% in ultrafiltration/diafiltration (UFDF). The uncertainty due to variability in the model parameter determination is less than 4.5% (DF) and less than 3.8% (UFDF). In the DF, a prediction of the final filter capacity was demonstrated from as low as 5.8% (9mbar) of the final transmembrane pressure (TMP). The scale-up based on DT in chromatography shows optimization potential in productivity up to a factor of 2. The schedule based on DT and PAT for APC has been compared to conventional process control, and hold-time and process duration reductions by a factor of 2 have been achieved. This work lays the foundation for the short-term validation of the DT and PAT for APC in an automated S7 process environment and the conversion from batch to continuous production.
Enhancing DPCD in Liquid Products by Mechanical Inactivation Effects: Assessment of Feasibility
(2020)
The enhancement of standard dense phase carbon dioxide (DPCD) pasteurization by additional mechanical effects was assessed in this work. These effects were induced during pasteurization by the sudden depressurization in a narrow minitube. The high flow velocities, moderate pressures (40–80 bar) and low temperatures (25–45 °C) lead to intense degasification and shear stress. The inactivation of the test microorganism Escherichia coli DH5α (E. coli DH5α) was determined before and after depressurization in the minitube, representing entirely chemical DPCD via dissolved CO2 and total inactivation comprising the effects of dissolved CO2 and mechanical effects, respectively. Compared to conventional DPCD pasteurization, which is mostly attributed to chemical effects, the additional mechanical effects increased the inactivation efficiency considerably.
Mit Hilfe der Inline-ATR-FTIR-Spektroskopie im mittelinfraroten (MIR) Spektralbereich lassen sich gleich mehrere Prozessparameter für Biogasanlagen in Echtzeit und ohne Probenahme verfolgen. Die gemessenen Absorptionsspektren geben simultan Aufschluss über den Gehalt an flüchtigen organischen Säuren (FOS), die alkalische Pufferkapazität (TAC) und die Ammoniumstickstoff-Konzentration (NH4-N).
Dabei können unter Verwendung intelligenter Datenanalyseverfahren, wie z.B. Partial Least Squares (PLS), Regression oder Support Vector Regression (SVR) sowie in kontrollierter Laborumgebung, Vorhersagefehler (RMSECV) von 0.372 g/l (FOS: R2=0.971), 0.336 g/l (TAC: R2=0.996) und 0.171 g/l (NH4-N: R2=0.992) im Falle der PLS, bzw. 0.386, 0.259 und 0.110 g/l für die SVR erreicht werden.
Erste Inline-Messungen in einer Biomüllvergärungsanlage zeigen, dass die erwarteten Absorptionsbanden auch im Prozessbetrieb wiedergefunden werden können. Sie unterliegen jedoch einem ausgeprägten Temperatureinfluss, der bei der Quantifizierung dieser Prozessdaten berücksichtigt werden muss. Weiterführende Untersuchungen sind notwendig, um die Inline-Tauglichkeit des Messsystems unter Beweis zu stellen.